Crown DriveCore CDi 4x600W Analog Power Amplifier
The CDi DriveCore Series is an evolution in amplification, providing an impressive mix of high-performance; rich feature set, and competitive cost. The CDi DriveCore 4x600 offers streamlined functionality to work in almost any large sized installation such as cinema, houses of worship, hotels, cruise lines, and more. The 4x600 includes network control/monitoring, high-level DSP, front-panel interface, and support for driving up to 100Vrms speaker loads without requiring a transformer.
Product Highlights:
Each output channel is capable of providing either 70V or 100V for high Impedance applications
Recall presets, mute channels, monitor faults, power on/off the amplifier, and more through a combined GPIO/AUX Port
Through HARMAN's HiQnet Audio Architect software, the CDi Drive Core can be controlled, configured, and monitored through standard TCP/IQ network
Completely configure the amplifier using an intuitive front-panel interface
On-board Digital Signal Processor in each amplifier allows for custom configuration
GPIO/AUX Port - Recall presets, mute channels, monitor faults, power on/off the amplifier, and more through a combined GPIO/ AUX Port
Key Features:
DriveCore Technology
Crown’s proprietary DriveCore technology eliminates hundreds of components within each amplifier, reducing the variability of component values, increasing reliability, resulting in incredible audio fidelity from an efficient design. Each output channel is capable of providing either 70V or 100V for high impedance applications.
Network Control and Monitoring
Through HARMAN’s HiQnet Audio Architect software, the CDi DriveCore can be controlled, configured, and monitored through standard TCP/IQ network. Both receive and send channels over HARMAN’s 256 channel, fault-tolerant audio BUS, BLU link (BL models only). Pre-loaded speaker tunings allow for quicker and easier setup and installation. For customized configurations, On-board Digital Signal Processor (DSP) in each amplifier allows for complete control using an intuitive front-panel interface. You can also recall presets, mute channels, monitor faults, power on/off the amplifier, and more through a combined GPIO/AUX Port.
Extended 6 Year Coverage
This protects you for a specific period from your date of purchase as stated in your bill of sale or as otherwise established by Harman. The coverage period will be extended to 6 years. Except as otherwise stated in this policy, this covers defects in materials and workmanship if: (1) you purchased this product from a dealer that is a Harman Professional authorized dealer with respect to this product at the time of your purchase; (2) your original, dated bill of sale is presented whenever service is required during the period; and (3) unless Harman states otherwise, you purchased this product in brand new condition.
Crown by Harman
Crown Audio is an industry leader in amplified sound. Crown makes amps for cinema venues, installed sites, touring rigs, portable PA and commercial audio. With over 67 years of focus on innovation and providing the best user experience, Crown Audio is continually raising the bar in audio amplification.
Product Specifications:
BLU Link: No
Channels: 4
Sensitivity (for full rated power at 8 ohms): 0.7V RMS
Rated Power Output (per channel at 4 ohms): 600W
Analog Input Signal to Noise Ratio (ref. rated power, 100V, 20Hz - 20kHz) at 8 ohms): greater than 104dB
THD (full rated power, 20 Hz - 20 kHz): 0.35 percent
Damping Factor (20 Hz to 100 Hz): greater than 1000
Frequency Response (8-ohm, 20 Hz - 20 kHz): +/-0.25dB
Crosstalk (below rated power) 20 Hz to 1 kHz: greater than 80dB
Input Impedance (nominally balanced, nominally unbalanced): 20 k-ohm balanced, 10 k-ohm unblanced
Dimensions (inches) (W x H x D) (depth not including 1.3 inch front panel protrusion): 19 x 3.5 x 12.25
Weight: 16.3 lbs (7.39 kg)
Power Supply Connector: 15A IEC connector, 100 - 240V